Corrosion properties of coatings produced from self-fluxing powders by the detonation spraying method
- Authors: Sirota V.V.1, Prokhorenkov D.S.1, Churikov A.S.1, Podgorny D.S.1, Alfimova N.I.1, Konnov A.V.1
-
Affiliations:
- Belgorod State Technological University named after V.G. Shukhov
- Issue: Vol 27, No 3 (2025)
- Pages: 151-165
- Section: Articles
- URL: https://ogarev-online.ru/1994-6309/article/view/308847
- DOI: https://doi.org/10.17212/1994-6309-2025-27.3-151-165
- ID: 308847
Cite item
Abstract
Introduction. This paper presents the results of a comprehensive study of the corrosion properties of innovative coatings based on self-fluxing NiCrBSi alloys (PR-NKh17SR4) modified with 10 wt.% boron carbide (B4C) nanoparticles, produced by detonation spraying. The relevance of the study stems from the critical need to develop new high-performance materials for protecting essential equipment operating under extreme conditions, including marine environments, chemically aggressive solutions, and elevated temperatures. Particular attention is paid to a detailed analysis of the influence of B4C on corrosion mechanisms, the formation of protective passivating layers, and the relationship between microstructure and functional properties of the coatings. Objective. A comprehensive evaluation of the effect of 10 wt.% B4C addition on the corrosion resistance, microstructure, and mechanical properties of coatings in comparison with the base alloy NiCrBSi alloy (PR-NKh17SR4) and the commercially available counterpart NiCr/WC alloy (VSNGN-85), widely used in industry. Methods. The coatings were applied to 0.40% C-Mn steel substrates using a multi-chamber cumulative detonation spraying unit (MKDU). Modern analytical methods were employed for thorough characterization: scanning electron microscopy (SEM, Mira 3) with energy-dispersive spectroscopy, X-ray diffraction (XRD, ARL X'TRA diffractometer) with quantitative phase composition assessment using the Rietveld method. Corrosion tests were conducted in a 3.5% NaCl solution simulating marine environments, using potentiostatic measurements and electrochemical impedance spectroscopy on a SmartStat PS-10-4 potentiostat-galvanostat. The depth of corrosion penetration was evaluated using confocal laser microscopy (Lext OLS5000) with a resolution of 10 nm. Results and discussion. It was established that the addition of 10 wt.% B4C leads to the formation of a unique multilayered coating structure with an amorphous phase content of up to 12.3% and promotes the formation of passivating chromium (Cr?O?) and boron (B?O?) oxides. Electrochemical measurements revealed an exceptionally low corrosion rate of 0.0014 mm/year, which is an order of magnitude lower than that of the base alloy (0.021 mm/year) and 30 times lower than that of the commercial counterpart NiCr/WC alloy (VSNGN-85) (0.041 mm/year). The modified coating exhibits remarkably high polarization resistance (215±25 kΩ·cm²) and minimal porosity (0.6±0.1%). The microhardness reached 680±40 HV, significantly exceeding that of the base alloy (520±30 HV), which is attributed to the formation of dispersed NiB? particles. XRD and EDS analyses confirmed the catalytic effect of B4C, facilitating a more complete transition of silicon into nickel silicide (NiSi). The developed coatings possess a unique combination of high corrosion resistance, wear resistance, and adhesive strength. The obtained results recommend this technology for creating protective coatings for critical components in the oil and gas industry, shipbuilding, and energy sectors. Future research prospects include optimizing powder compositions and spraying parameters for various operational conditions, including elevated temperatures and combined loads.
About the authors
Vaycheslav V. Sirota
Belgorod State Technological University named after V.G. Shukhov
Author for correspondence.
Email: zmas36@mail.ru
ORCID iD: 0000-0003-4634-7109
SPIN-code: 4397-7051
Scopus Author ID: 6603006348
ResearcherId: W-6662-2019
Ph.D. (Physics and Mathematics), Director of the Center for High Technologies
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationDmitrii S. Prokhorenkov
Belgorod State Technological University named after V.G. Shukhov
Email: bstu-cvt-sem@yandex.ru
ORCID iD: 0000-0002-6455-8172
SPIN-code: 8338-2861
Scopus Author ID: 12646543400
ResearcherId: E-2320-2014
Research Engineer
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationAnton S. Churikov
Belgorod State Technological University named after V.G. Shukhov
Email: churikov.toni@mail.ru
ORCID iD: 0000-0002-1829-2676
SPIN-code: 4046-1033
Scopus Author ID: 58637258900
ResearcherId: GYA-1311-2022
Research Engineer
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationDaniil S. Podgorny
Belgorod State Technological University named after V.G. Shukhov
Email: dan_podgor@mail.ru
ORCID iD: 0000-0001-7435-5005
SPIN-code: 3513-0430
Scopus Author ID: 57222400221
ResearcherId: ABD-9978-2021
https://www.researchgate.net/profile/Daniil-Podgornyi
Research Engineer
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationNatalia I. Alfimova
Belgorod State Technological University named after V.G. Shukhov
Email: alfimovan@mail.ru
ORCID iD: 0000-0003-3013-0829
SPIN-code: 4098-5249
Scopus Author ID: 55886640800
ResearcherId: ABF-4151-2020
https://www.researchgate.net/profile/Nataliya-Alfimova
Ph.D. (Engineering), Associate Professor
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationAndrey V. Konnov
Belgorod State Technological University named after V.G. Shukhov
Email: andrekonnov555@yandex.ru
ORCID iD: 0009-0009-3245-0747
Laboratory researcher
Russian Federation, 46 Kostyukova st., Belgorod, 308012, Russian FederationReferences
- Simunovic K., Saric T., Simunovic G. Different approaches to the investigation and testing of the Ni-based self-fluxing alloy coatings – A review. Part 1: General facts, wear and corrosion investigations // Tribology Transactions. – 2014. – Vol. 57 (6). – P. 955–979.
- Cost of corrosion in the United States // Handbook of environmental degradation of materials / G.H. Koch, M.P.H. Brongers, N.G. Thompson, Y.P. Virmani, J.H. Payer. – William Andrew Publishing, 2005. – P. 3–24. – doi: 10.1016/B978-081551500-5.50003-3.
- Thompson N.G., Yunovich M., Dunmire D. Cost of corrosion and corrosion maintenance strategies // Corrosion Reviews. – 2007. – Vol. 25 (3–4). – P. 247–262. – DOI: 0.1515/CORRREV.2007.25.3-4.247.
- Baorong H.O.U., Dongzhu L.U. Corrosion cost and preventive strategies in China // Bulletin of Chinese Academy of Sciences (Chinese Version). – 2018. – Vol. 33 (6). – P. 601–609. – doi: 10.16418/j.issn.1000-3045.2018.06.008.
- Wear behavior of a borided nickel-based self-fluxing thermal spray coating / F.E. Mariani, G.C. Rêgo, A.L. Neto, G.E. Totten, L.C. Casteletti // Materials Performance and Characterization. – 2016. – Vol. 5 (4). – doi: 10.1520/MPC20150064.
- Microstructural analysis of flame-sprayed and PTA-deposited nickel-based self-fluxing alloy coatings / I. Vidakovic, K. Šimunovic, G. Heffer, V. Špada // Welding in the World. – 2024. – Vol. 68 (11). – P. 2819–2836. – doi: 10.1007/s40194-024-01814-5.
- Justification of strengthening of working bodies of forestry machines with self-fluxing alloys during gas-flame spraying / V.I. Kretinin, A.V. Teppoev, V.A. Sokolova, O.A. Polyanskaya, S.V. Alekseeva // IOP Conference Series: Earth and Environmental Science. – 2021. – Vol. 876 (1). – P. 012045. – doi: 10.1088/1755-1315/876/1/012045.
- A novel strategy for depositing dense self-fluxing alloy coatings with sufficiently bonded splats by one-step atmospheric plasma spraying / X.Y. Dong, X.T. Luo, S.L. Zhang, C.J. Li // Journal of Thermal Spray Technology. – 2020. – Vol. 29. – P. 173–184. – doi: 10.1007/s11666-019-00943-4.
- Effect of flame remelting on the microstructure, wear and corrosion resistance of HVOF sprayed NiCrBSi coatings / C.W. Liu, E.W. Qin, G.X. Chen, S.C. Wei, Y. Zou, L. Ye, S.H. Wu // Advanced Materials Research. – 2024. – Vol. 1179. – P. 157–168. – doi: 10.4028/p-v2xcOL.
- Influences of flame remelting and WC-Co addition on microstructure, mechanical properties and corrosion behavior of NiCrBSi coatings manufactured via HVOF process / S. Shuecamlue, A. Taman, P. Khamnantha, C. Banjongprasert // Surfaces and Interfaces. – 2024. – Vol. 48. – P. 104135. – doi: 10.1016/j.surfin.2024.104135.
- Shabanlo M., Amini Najafabadi R., Meysami A. Evaluation and comparison the effect of heat treatment on mechanical properties of NiCrBSi thermally sprayed coatings // Anti-Corrosion Methods and Materials. – 2018. – Vol. 65 (1). – P. 34–37. – doi: 10.1108/ACMM-02-2017-1756.
- Temperature profile, microstructural evolution, and wear resistance of plasma-sprayed NiCrBSi coatings under different powers in a vertical remelting way / H.N. Xuan, L. Chen, N. Li, H. Wang, C. Zhao, M. Bobrov, S. Lu, L. Zhang // Materials Chemistry and Physics. – 2022. – Vol. 292. – P. 126773. – doi: 10.1016/j.matchemphys.2022.126773.
- Fayomi O.S.I., Akande I.G., Odigie S. Economic impact of corrosion in oil sectors and prevention: an overview // Journal of Physics: Conference Series. – 2019. – Vol. 1378 (2). – P. 022037. – doi: 10.1088/1742-6596/1378/2/022037.
- Kania H. Corrosion and anticorrosion of alloys/metals: the important global issue // Coatings. – 2023. – Vol. 13 (2). – P. 216. – doi: 10.3390/coatings13020216.
- Shekari E., Khan F., Ahmed S. Economic risk analysis of pitting corrosion in process facilities // International Journal of Pressure Vessels and Piping. – 2017. – Vol. 157. – P. 51–62. – doi: 10.1016/j.ijpvp.2017.08.005.
- High-velocity collision of hot particles with solid substrate, under detonation spraying: detonation splats / S.B. Zlobin, V.Yu. Ulianitsky, A.A. Shtertser, I. Smurov // Thermal Spray: Expanding Thermal Spray Performance to New Markets and Applications. – ASM, 2009. – P. 714–717. – doi: 10.31399/asm.cp.itsc2009p0714.
- Tucker R.C. Jr. Structure property relationships in deposits produced by plasma spray and detonation gun techniques // Journal of Vacuum Science and Technology. – 1974. – Vol. 11 (4). – P. 725–734. – doi: 10.1116/1.1312743.
- Sundararajan G., Sen D., Sivakumar G. The tribological behaviour of detonation sprayed coatings: the importance of coating process parameters // Wear. – 2005. – Vol. 258 (1–4). – P. 377–391. – doi: 10.1016/j.wear.2004.03.022.
- Detonation application of a hard composite coating to cutters for centrifugal beet shredders / V.V. Sirota, S.V. Zaitsev, D.S. Prokhorenkov, M.V. Limarenko, A.A. Skiba, A.S. Churikov, A.L. Dan’;shin // Russian Engineering Research. – 2023. – Vol. 43 (9). – P. 1142–1145. – doi: 10.3103/s1068798x23090216.
- The effect of the introduction of B4C on the adhesive and cohesive properties of self-fluxing coatings / V.V. Sirota, S.V. Zaitsev, M.V. Limarenko, A.S. Churikov, D. S. Podgornyi // Construction Materials and Products. – 2024. – Vol. 7 (6). – doi: 10.58224/2618-7183-2024-7-6-5.
- impedance.py: A Python package for electrochemical impedance analysis / M.D. Murbach, B. Gerwe, N. Dawson-Elli, L. Tsui // Journal of Open Source Software. – 2020. – Vol. 5 (52). – P. 2349. – doi: 10.21105/joss.02349.
Supplementary files
